A brand of LEIT

Cleaning and periodic inspection: how do you keep your plant producing?

Clean glass and inspections on time are what keep your plant producing. Here you learn when and how to clean, what your own staff may do safely and what is left to a qualified technician.

By the engineering team at pv.directLast updated: 21 November 2026

Why cleanliness matters.

Panels work with the light that passes through their glass. A layer of dust blocks part of it, so production falls without any fault showing.

In a published experiment in Cairo in spring, a small test panel left uncleaned had lost more than 10% of its measured efficiency by the third week. The figure differs from site to site, but it shows the scale.

The Cairo experiment, published in Scientific Reports

Rain is rare in Egypt, so dust is not washed off by itself. Dew fixes it to the glass, so the longer cleaning waits, the harder it becomes. Dust has more than one source:

  • Airborne dust and dust storms, especially the khamsin in spring.
  • Industrial dust: cement, textile lint and stack exhaust.
  • Unpaved roads and lorry traffic around the site.
  • Bird droppings.

A spot that covers a small part of a panel, such as bird droppings, can cut its production by more than its size and heat the cells beneath it. That is why such spots are removed as soon as they appear.

Shading in the glossary

What is checked, and where.

A periodic inspection covers six places, from the glass to the meter. Checking by eye is your staff's job; any opening, measuring or tightening is the job of a qualified technician.

123456
Illustrative drawingA simplified plant on a site's roof; the numbers mark the places that are inspected.
  1. The glass surface. Dust, spots, bird droppings or a crack. A crack is reported and not touched.
  2. The panel frames and the bolts of the mounting structure. A loose bolt, a clamp that has moved out of place, or rust. The tightening itself is a job for a qualified technician.
  3. The cables and connectors. By eye only, without touching: a hanging cable, cracked insulation or a connector with heat marks. Connectors are never opened.
  4. The inverter. The ventilation openings are not blocked, the filters are clean where there are filters, and the display or the status indicator shows no alarm.
  5. Earthing and protection devices. The earthing conductor is connected and intact, and the isolating switch and the breakers are in their normal position.
  6. The meter and the production reading. The bidirectional meter records what your site drew from the grid and what it exported to it. The production figure itself is recorded by the inverter, and it tells you whether the plant is running as expected.

How often?

No single number fits every site. The intervals depend on:

  • The dust around your site: desert, a road, a cement plant or a quarry nearby.
  • The tilt of the panels: the flatter they lie, the more dust stays on them.
  • The season: the dry months and the khamsin differ from the rainy months.
  • Birds, humidity and dew.

On dusty sites the panels are usually cleaned once a week or every few weeks in the dry months, less often in the rest of the year, and after any dust storm.

Let the production reading decide. Compare each month's production with the estimate in your offer and, after the first year, with the same month a year earlier. If production on clear days rises markedly after each cleaning, shorten the intervals; if the difference is small, lengthen them.

Capacity and production: kWp and kWh

Common intervals, as an illustration; they are adjusted to your site, your contract and the manufacturers' instructions.
TaskWho does itHow often
The inverter's indicator and the production readingYour staffEvery week
A walk-round visual check of the plantYour staffEvery month, and after any storm
Cleaning the glassTrained staff, as your contract sets outAs the dust requires, and after storms
Electrical inspection with measurementsA qualified technicianCommonly once a year
Checking the bolts for tightness and the structure for rustA qualified technicianCommonly once a year

Cleaning safely, step by step.

Cleaning the wrong way can crack or scratch the glass and affect the manufacturer's warranty. These steps are common practice; your panel manufacturer's instructions take precedence, and whoever cleans must be trained in them.

  1. Choose the time. Early in the morning or towards sunset, when the glass is cool and there is still enough light to work safely. Cold water on hot glass can crack it.
  2. Check before you start. A panel with broken glass or an exposed cable is not washed, and neither are the panels around it. Stop cleaning that part and tell the technician.
  3. Use clean water that is low in minerals. It leaves no deposits on the glass. No solvents and no harsh detergents.
  4. Wipe with a soft brush or a soft cloth. Wet the glass first. Abrasive tools scratch it, and grains of sand under them make the scratches worse.
  5. Avoid high pressure. A high-pressure jet at close range can damage the panel, its edges and its connectors.
  6. Do not walk on the panels. Do not lean on them either. The weight causes fine cracks in the cells that the eye cannot see.
Every trip onto the roof has its rules: a safety harness fixed to an anchor point where the roof slopes or has no parapet, non-slip shoes, and nobody goes up alone. Skylights and rusted roof sheets do not carry a person's weight and must never be walked on.

What your staff must never do.

The direct-current side, from the panels to the inverter, stays live as long as there is daylight, even when the inverter is off and the main breaker is open. So your staff must never:

  • Open a connector, a junction box or the cover of the inverter.
  • Touch or wash a broken panel or a damaged cable.
  • Spray water on the inverter, the electrical panels or the connectors.

If the walk-round shows a broken panel, a damaged cable or an open connector, photograph it from a distance and report it to the technician.

Safety: isolation and what to do in a fire

Who is responsible for what.

Maintenance is included in the first year, as your offer states. The scope of maintenance, cleaning and repairs is what your offer and your contract set out.

The installation work and maintenance are the responsibility of our Egyptian company, LEIT Energy Consulting LLC, as the contract sets out. Equipment warranties come from the manufacturers on their terms.

The net-metering rules issued by Egypt's electricity regulator in February 2026 oblige the owner of a plant of 100 kW alternating current or more to hold a maintenance contract with the qualified company once its warranty ends, with yearly maintenance reports to the distribution company. The owner of a smaller plant must hold a contract for remote follow-up of its performance.

Egyptian Electric Utility and Consumer Protection Regulatory Agency: the net-metering rules (in Arabic)

Before you sign, ask:

  • Is cleaning the glass within the scope, or is it for my staff? And how often?
  • What does the periodic inspection cover, and at what intervals?
  • What are the cleaning instructions of my panels' manufacturer?
  • Where do I read the production figure?
  • If production falls or the inverter stops, whom do I tell?
  • What is outside the scope?

Contract and signature

Your request's pathShort questions, A price on the screen, A written offer within one working day, The contract, Survey and installation

Your project file starts with your first answer.

Tell us a few details about your site; our team reviews them and prepares a preliminary study for you.

Start designing your plantTalk to an engineer